Clarinet Systems ESB101 Betriebsanweisung Seite 24
- Seite / 71
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
3-4
A proprietary infrared communication link is established enabling you to make IP
configuration changes. However, this option does not provide a mean to update
firmware nor allow the user to configure switches other then the one connecting to.
For managing multiple network Switches or updating the firmware, follow the steps in
Configure via IP address on the following section. Nevertheless, this option provides
the mean to configure the switch without an Ethernet uplink or invalid IP address
settings.
Configure via IP address
The CSI Configuration Tool can be installed and launched on a PC running Windows
95/98/ME/2000/XP and connect to any Switch on the network provided the TCP/IP
settings of its Ethernet adapter card is configured to be on the same subnet as the
EthIR Switch. Laptop using an Ethernet card or utilizing ClarinetIR™ for LAN
connectivity also applies. The following step describes how to start configuration
using Ethernet connection:
1. Make sure Ethernet connectivity is available and switch is on the network.
2. Launch the Configuration Tool software.
3. Click the Configure via IP address.
4. Search for the switch via either range search or search for specific IP.
5. Click on the IP address of the switch to be configured.
6. Click the Edit Configuration.
This method is best suited to manage a Switch that has already been properly
configured. However, if an infrared notebook is not available for initial Switch
configuration, a Palm based configuration tool is also available for initial
configuration.
Setting The IP Address Of The Switch For The First
Time
If the EthIR Switch will be managed by SNMP or support IR/PPP devices, it must
have an IP address. Since ES1000 may work as a standalone device with no need of
uplink connection, it does need IP addresses in such case.
All EthIR Switches except ES1000 are shipped with DHCP option turned on so no
configuration is needed if you have a DHCP server deployed on your network.
The users who wish to assign static IP addresses can follow the instructions below by
uncheck the use DHCP option. To avoid possible IP conflicts you should reset the
Switch’s IP of those models before connect the uplink to an existing network. Again,
do not uplink the Switch to an existing network when performing the initial
configuration.
- EthIR LAN 1
- User Guide 1
- EthIR LAN® User Guide 3
- TABLE OF CONTENTS 5
- Chapter 1 9
- Introduction 9
- Appendices 10
- Conventions 10
- Contacting Clarinet Systems 11
- Chapter 2 13
- Installation 13
- Figure 2-1 15
- N/A N/A N/A ON N/A 17
- 216 only) 18
- EthIR Beam 19
- ClarinetIR™ 20
- CSI Firmware updates 20
- Chapter 3 21
- Configuring EthIR LAN 21
- Configure via Infrared 23
- Configure via IP address 24
- Searching For EthIR Switches 26
- The NVM Editor 28
- SNMP Variables Tab 29
- RF Card Info (ESB3011B only) 30
- WEP (ESB3011b only) 31
- Updating The Firmware 32
- Switch Security 32
- Chapter 4 33
- ClarinetIR 33
- APPENDIX A 35
- APPENDIX B 41
- APPENDIX C 43
- APPENDIX D 45
- APPENDIX E 47
- APPENDIX F 51
- Infrared Monitor as follows: 52
- Microsoft IrLAN 54
- Notebooks 55
- Add/Remove Program icon in 56
- Add/Remove dialogs: 56
- Details button 57
- Click OK 58
- Direct Cable Connection 58
- Guest then click the Next 58
- Cancel 59
- File\Desktop 66
- Shortcut 66
- and click 67
- Apple Menu\Control 68
- Configuring Palm Organizers 69
Minka Lavery 1290-648 manuály
Uživatelské manuály a uživatelské příručky pro ne Minka Lavery 1290-648.
Poskytujeme 1 manuály pdf Minka Lavery 1290-648 ke stažení zdarma podle typů dokumentů: Manuál s instrukcemi
Kommentare zu diesen Handbüchern